Clearwater, FL

Checked all major come on the ac unit: compressor fan motors , capacitor, Freon levels, temp differentials, flushed drain line, checked filters. Based on readings Capacitor was lower than it is rated which means that is going bad and need to be replaced . Also compressor has started to work hard and need to add a hard start kit on to make it work smoother. Blower wheel is dirty and need to be cleaned. Customer want to schedule the capacitor for another day.

Checked all major come on the ac unit: compressor fan motors , capacitor, Freon levels, temp differentials, flushed drain line, checked filters. Based on readings unit Is working good for now. The armored on the suction line outside was ripped off and replaced 7 feet of it. Also recommend to customer to add a hard start kit to make compressor work smoother

4 new returns, 9 new supplies. Permits and inspections included. New 5 inch media filter. 5 year parts and labor guarantee on ductwork. all new ductwork installed after tear out of all metal ductwork, new Plenum new heat shield, new media filter on return Air side 34 new cutting for return Air pictures taken of all work completed supply trunk lines ran to mixing boxes mixing boxes to the diffusers everythingt to has dampers at mixing boxes for supplies complete

Replaced condenser fan motor out of warranty and also unit was undercharged and added 3 lb of freon . Unit is working good now. Customer may be interested in membership

Customer complaining no cool. After evaluating the entire system noticed that outside fan motor was bad and wasn’t coming on . Need to check for warranty and give the quote . Motor need to be replaced

Upon arrival customer said that unit is not turning on. Outside unit was working but the blower inside is not coming on . The blower is bad . And blower wheel is dirty and need to be clean . Customer accepted to go ahead and do the service . Need to schedule another day for replacing the blower motor when we have it. Day 2: replaced blower motor , cleaned blower wheel, flushed drain line, checked the Freon and it was low the shrewder valve was leaking, replaced shrewder valve and add 1 pound of Freon. Customer is aware of maintenance membership.

Customer said unit is not cooling . Checked the Freon level were nearly 0 added e little bit of Freon and pressure test it with nitrogen and checked with sniffer and it was leaking from the evap coil . Customer need a quote for replacing the evap coil

Ruud 2 Stage Heat Pump Full system horizontal install includes: Remove and dispose of existing equipment and materials,Install new air handler in existing location, Install new outdoor unit and pad at existing location to code, New hang kit, drain pan, float switch. Safety overflow switch for drain line. Verify proper condensate drainage with Drain Solve. Mastic seal immediate duct connections. Recover refrigerant per EPA standards. Flush line-set. Charge system to ensure maximum efficiency. Adjust fan speed if necessary to accommodate static pressure of ductwork. Electrical safety: We will ensure your system is installed safely and according to code. Any unforseen electrical not included in initial proposal will be at the expense of the homeowner. Complete clean-up including drop cloths and shoe covers. Permits and Inspections of AHRI certified equipment to code. All work to be performed in a neat and professional manner in accordance with existing codes by trained technicians. 1

Media Replacements Filter 20x20

Uv light is in good working condition. Found dirty filter, highly recommended replacing. Customer ordered new filters from filterbuy. Found buildup by one of the supply grills, the grill wasn’t flush with the ceiling. Tightened grill to ceiling. System is working properly. - Collin

Upon arrival, found system off, not working. During inspection found blown five and fuse.Tstat was wired wrong with common in the wrong terminal. Also float switched failed not allowing 24v to kick the system on. Recommend replacing float switch and 5 amp fuse .

Customer did not want a maintenance done today when she called into the office she said that she needed to have the upstairs air handler in the closet cleaned of mold, which would include cleaning the blower and blower assembly. Also doing a very deep clean on the evaporator coil. The last time that Dakota was out here he let this customer know that they could call Dell air and have their blower motor replaced because it was under warranty. When Del air came out and replaced the blower motor, they also did the entire maintenance on all the systems. That was right before Christmas. Also she said that Dakota was here in September and did the maintenance and he was the one who suggested that they Get the upstairs air handler cleaned I let this customer know I said I apologize for the confusion. I gave her pricing for the Pull and clean on the blower and blower assembly and I also gave her the price for cleaning the evaporator coil. I let her know if she renewed that 20% would be taken of

Installation of Packaged Unit. All work to be performed in a neat and orderly manner in accordance to existing codes by trained and certified technicians. Upon arrival, meet and greet with customer go over Work scheduled for the day tear out existing package unit replace new package unit on existing pad. That’s concreted in tie down. Four corners. Hook up new high voltage whip to new pull out. Disconnect hung on wall electrical is neatly ran Hook up supply Plenum and return Plenum mastic and seal all the way around pictures taken of all work completed start up. Everything is checked in corn heat modes had to reprogram thermostat to get to work and heat mode. Everything is complete put tarp over ductwork until we get dog house, have dog house, measurements, and paperwork .

2 Mini Split Condensate Pumps Installed Condensate Pumps. Need to return to diagnose why the mini splits are not going on on call for cooling. Tested condensate pumps and they are pumping water out. 12/13/24: diagnostics for mini splits and found fuses for the New condensate pumps are blown. Need to replace According to the Goni II manual (Photos), FUS-4180/10 Pt#: 3004180 Fuses 5x20 6.3A, 10pcs. Fuses are internal to the pumps - New pumps may be needed as these are bad out of the box. Upon return, will need to shorten condensate wires to be able to tuck them at the rear of the air handler head. 12/17/24 Returned and replaced the pumps and shortened the wire leads. Turned the systems on and tested the pumps. Once pan was filled the pump activated and pumped the water out. Systems are cooling.

Arrived to perform preventative maintenance on their cooling and heating system. Cleared all drain lines, checked all float switches, check capacitors changed all filters systems are all heating and cooling

Checked pressures, temperatures, and amp draws. Found weak cap for blower motor. Replaced upon approval. Also found pitting contractor. Replaced upon approval. Recommended air quality products and surge protection. Customer declined. System is now working and draining properly. - Collin

Installed warranty blower motor, primary float switch, dual uvc IAQ product, and air handler surge protector. Checked all operations. Flushed drain assembly. Replaced filter. System is working and draining properly. - Collin

Unit #2: found breaker mislabeled and completely shut off at the panel. Turned on and checked voltages, received 240v. Turned off to check to ground and not shown. Turned back on and checked the system and operating. Unit#1: Operating. DO NOT ORDER-Homeowner had Del-Air out to replace the motor back in May. She called them, and they will replace under warranty. Unit #3 (Master Bdrm): need to replace evaporator fan motor. Carrier M/N: FB4CNP042LOOAAAA S/N: 1415A87287

Customer purchased membership per Collin on 10- 17–24. Performed inspection one of two. Checked pressures, temperatures, and amp draws. Found rusted filter drier by condenser, growth on blower assembly, no primary float switch, drain line missing insulation, no surge protection, dirty whole house filter, and Uv light not working. Highly recommend taking care of these issues. Customer will be replacing filter himself. Flushed drain assembly. System is working and draining at this time. - Collin

Electrical Arrived to find system coming on, but the compressor would not come on. There was a burnt wire coming from the contactor to the capacitor not giving it the voltage it needed. I checked the capacitor it was a 45/5 micro run capacitor it was good I replaced that burnt wire and the system started cooling. My pressures were good. The people that live here are out of town for three months. The gentleman that’s occupying this place, his house was underwater and he’s staying here until he can get back up on his feet. I cannot get to the air handler the people that own this house. Their car was in the way and the gentleman said he didn’t know where the keys were at I did suck out the drain line and remove some buildup this system is cooling properly at this time

System not running due to electrical issue feeding main electrical panel with 240V. Not able to start a unit due to this issue. Advised customer to call Duke Energy or electrical company to resolve this issue. Possible issue is that something got wet and failed during a storm

Need oxidizer replacement and dual uvc bulb replacement. Checked pressures, temperatures, and amp draws. Found speed tap for blower motor set to 4. Adjusted speed tap to 2 upon approval from customer. This will take more humidity out of the air. Checked temperature split. All within factory specifications. Customer purchased plan per Collin on 9-23-2024. Flushed drain assembly. Installed oxidizer replacement and dual uvc bulb replacement. System is working and draining properly. - Collin

Came for a service call this gentleman was home on lunch Thought this would be an easy fix. It wasn’t just the UV light that he needed. He needed the fixture that the light goes into. It was melted. I opened up a pure air X RMS one but the fixture was different. He had to go back to work what we need to do is replace the whole thing ballast and put a new UV light with the new fixture to make this work. Unless We have one that’s compatible for his UV system other than that customer had no complaints, thank you for choosing Total Air

Leak search Office please follow up with the customer. 1. Holding off on replacing the contactor until lineset is replaced. 2. Performed full leak search on indoor and outdoor unit. Did not get any hits. Leak search hit was found at the lineset that goes underground (see video). 3. We will need to send Josh or Casey back to cut into the drywall above the kitchen area to verify if we can run a lineset above the kitchen cabinets, out the utility closet, and then outside. Customer is aware he will need to pay for drywall repairs regardless if the plan will work. 4. Please have Casey or Josh get a signature from customer about drywall repairs and refer our drywall company. 5. Lindsey, please provide customer with estimate for running new lineset. 6. Thermostat wire is also older and should be replaced from the air handler to the condenser. Materials needed (have Josh or Casey Verify other materials if needed) Approximately 1 roll of copper 50’ 2 Installers, 1 day Filter drier Roughly

Came to perform a preventative maintenance. This air handler is in the attic it’s a 2014 train heat pump split system when I got here. The customer had a hose coming from the attic where she was siphoning out water into the shower because they left the float switch up so it system would run which overflowed into the secondary drain pan, cutting it off, this is a Tam TAM TRANE UNIT Which means that this unit is positively pressured which means you do not need a trap on this unit and this unit has a trap on it. You can’t remove the trap because the drain line goes underground and then pops up. I cleared the drain line and made sure that it was cooling properly checked all operations amp draws the filter sizes a 20 x 24 x 1 The run capacitor is a 45/7.5 µF run capacitor is well within range. The UV light is working. Their float switches both work because they had to prop one up by putting tape around the rim of it so it would not sit fully down in the float switch holder, allowing water t