Seminole, FL

3 Duct Run Replacements Furnish and Install Flex Duct 4" / 6" Furnish and Install Splice Collars Mastic Tape Mastic Recommended Rodent Remediation / Inspection Prior to work being completed. Upon arrival, meet and greet with customer go over Work scheduled for the day get started upon access to attic noticed that the job entails more than expected took pictures of all items found destroyed that beautiful new ductwork and unfortunately missa is going to need a new system installed. As of now we have replaced a couple runs and patched all ductwork necessary to keep running until we get out to estimate after she’s confirmed that the rats Are no longer in attic one of the worst infestations I’ve seen

Completed full maintenance on split system unit Checked all wiring and components Checked refrigerant levels and temperature I had a little leak in hoses, added 1 lb of refrigerant. Tested capacitor, reading 40.9/45 told customer he needs to replace it. Installed new one on site 45/5 Tested fan and compressor amps Tested blower fan amps Tested float switch Took temperature splits from return and supply Vacuumed and flushed condensate line Unit is up and operating at this time

Clean Condensate Line with Drain Solve Install IFlow System for Drainage - Better Monitoring Perform Start Up Procedures

Customer complained no cool. Thermostat is blank. There is no hight voltage coming to A/H . Checked the breaker there is a voltage there not not coming to the disconnect box. Customer has to check with an electrician

Replaced fan motor under warranty . Unit is operating good

It was detected that the fuse was bad and the capacitor was low The fuse and capacitor were changed Checked refrigerant level and temperature Took air temperature on supply and return Tested float switch Vacuumed flushed condensate drain System is running and operating at this time

Seal any leaking ductwork you see with spray glue, tape, then mastic.

Arrived on site for no heat found system heating, but not properly. Heat pump was working to full capability but aux heat was not turning on simultaneously. Programmed T- stat so aux heat can come on with heat pump at a certain temperature. System is now heating properly at this time.

Upon arrival found unit operating checked all major components to specifications also flushed out the drainage system with water and shop vac checked all wiring for breakage and corrosion customer declined on all other upgrades and repairs to system customer is satisfied with work performed today unit is operating efficiently at this time

Upon arrival found that both units were operating checked all major components to spec changed and washed all filters and checked all wiring connections to spec customer is satisfied with work performed units are operating efficiently at this time

Manufacturer Daikin Model # RXB12BXVJU Serial # K004465 Need outdoor control board unsure of warranty Need to get pricing and let customer know Found board not working properly with heat mode. System works properly in cooling. Will need to replace control board in condenser to be able to check through system throughly. - Collin

Used 2 pole contactor Used T6 pro thermostat Upon arrival found Trane system is closet by kitchen not heating. Found shorted electric heat 24v contactor coil. Replaced contactor upon approval. Also found t6 thermostat with bad heat circuit. Replaced thermostat upon approval. Checked operation. System is now heating properly. Customer would like maintenance performed on systems please. - Collin

Customer stated he replaced the thermostat himself. Then put the old one back on. Found blown fuse. Replaced fuse. Checked operation. System is working and draining properly. Thermostat is not working properly. Recommended to install customer supplied Tstat and customer declined. - Collin

Mini split head coil and blower cleaning Removed plastic covers. Soaked plastic pieces in coil cleaner, rinsed and allowed to dry in the sun. Cleaned mini split head with a bib. Evap coil and blower wheel both had a very thick layer of microbial growth. Used 6 rounds of coil cleaner to remove all dirt and growth. Reassembled mini split head and restarted the system. There is a noticeable difference in air temp and speed after cleaning.

Replaced outdoor inverter board. Once replaced let the system run for 20 minutes. Left working and in cooling mode. The indoor air handler shakes a little when on the highest fan speed. This could be because of the mounting brackets. May need to make future adjustments. For now customer keeps it set at 70° and a lower fan speed. Flushed drain line and air handler over filled. Found the flex drain connect to the pvc was kinked and not in the pvc, hence why it was not draining properly. Reconnected flex and pvc and taped up. Flushed drain again and it’s draining properly. Supply temp is 36° return 67°. Set thermostat control back to 70°.

Arrived at th job and th homeowner was able to bypass th condensate pump. It was under water and shorted. Homeowner agreed to replace the condensate pump. Replaced the pump, attached the plug and low voltage. Homeowner had a concern of wet insulation inside the return plenum coffin box. Opened the ductwork and inspected the insulation. Once opened pressed on the insulation and there was no Indication of water seeping out. It is dry from the area that is inspected.

Used IFLO Pro device and bottle of formula ! Customer purchased membership per Collin on 9-26-2024. Upon arrival found system off on the float switch. Flushed drain assembly and installed IFLO pro device with formula bottle upon approval. Checked pressures, temperatures, and amp draws. All within factory specifications. System is working and draining properly. Will need to replace formula bottle for IFLO PRO every 6 months. - Collin

Customer stated water leaking under air handler. After further inspection found that internal drain pan was full of debris and slime. Drain line was fully flushed and cleaned. Internal drain pan was cleaned as well. Made sure that system is draining properly. Checked refrigerant charge. Inspected air filter. Offered maintenance plan to the customer but they will be selling a house very soon. System is running well at this time without any issues

Upon arrival found no signal for cooling at the condenser. Upon further inspection found corroded and broken yellow wire for contactor coil. Repaired wiring upon approval. Checked pressures, temperatures, and amp draws. All within factory specifications. System is working and draining properly. - Collin

Office: Mr. McCoy will call in for payment. cap rArrived at the home and proceeded to find a way under the trailer. Needed to enter from the rear of the home. Removed old duct work from the equipment including the “T”. Replaced the flex runs from the home to the “T” and to the unit. Panduit strapped, mastic tapped and added mastic to seal duct work. Checked refrigerant charge and looks good. Send Luis back in 2 weeks to do a check on the system. 9/3/24: upon arrival met with the one owner and proceed to install new duct cover. Sealed all around the unit and up to the home. Began with check up of the equipment. Pressures were going up when adding a small amount of refrigerant. Sub cooling and super heat were off along with pressures rising. Removed the old refrigerant and checked the piston and found it clear of any debris. Replaced piston and began to pull a vacuum. Once it was completed, added refrigerant into the system and brought it to manufactures specifications of 5 lbs.

Return to perform wall-mounted mini split cleaning. Removed door and blower fins. Wrapped head unit with a bib and soaked evaporator coil and blower wheel in coil cleaner. Washed away all coil cleaner and microbial growth with water. Allowed Time for system to dry. rewired and restarted the system.

Complaint of system not cooling properly. Diagnosed that dual run capacitor had failed causing compressor not to turn on. Replaced it with a warranty part and made sure system is cooling properly. Checked refrigerant charge. Inspected rest of electrical inside a condenser. Highly recommend surge protection installed at condenser unit to protect it from power surges,lightning’s and electrical brownouts customer was encouraged to sign up for a yearly membership maintenance service to prevent future issues with a system. Quote will be emailed to the customer fora surge and maintenance program. No other issues ar found at this time. System is cooling well without any issues

Performed system PM on both units. Office materials added 4lbs 410a #326 Checked electrical components, filters, cleared and flushed drain lines, refrigerant levels, and temperatures. The upstairs Rheem unit was low on refrigerant. Adjusted levels to factory range and performed a leak search. Did not get any hits, we will need to continue monitoring levels on the next visit. Possible we will need to perform a more in depth leak search. Upstairs nest thermostat gave a wire error twice in the last month. This could be starting to fail. Estimate added for replacement nest. It also may have been a drain clogg that triggered it to stop working.

Arrived to perform maintenance on one mini split split system manufacturer is Midea. While I was there, they asked about getting their other system maintenance. I went ahead and added them onto the membership for a second system. The second system has one condensing unit and two heads. One is in the master bedroom. One is in his art room. The main system downstairs has a mini split condenser, but an air handler in the closet changed out the electrostatic fiber in the filter. Check operations make sure drain lines were clear all the systems are cooling properly at this time