St Petersburg, FL

Unit was low on Freon checked for leaks but didn’t find any Added 1 lb of Freon and unit is cooling properly now. If the problem is repeated again we need to do a pressure test on the copper line to see where the leak is

Bandaid

The client did not accept the membership and said he would call whenever he thought it was necessary. the capacitor was bad and had to be replaced 40/5 Completed full maintenance on split system Checked capacitor and contactor Checked compressor and fans amps Checked refrigerant levels and temperature Vacuumed and flushed condensate drain Replaced filter Took air temperature on supply and return System running and operating at this time

Chech all electrical components, check the refrigerant pressure,cleaning clean drain line . Recommend hard start and blow more cleaning and UV light.

The capacitor and the hard start kit were bad, these were replaced, the system was low on Freon, the customer rejected the leak test and two pounds of Freon were added. Vacuumed and flushed condensate drain System running and operating at this time

1 pole contactor 35/5 capacitor The contactor was bad and the capacitor was low, these two were replaced Flushed condensate drain System running and operating at this time

SEND AN ADVISOR TOMORROW IN THE MORNING The unit has no freon, it is completely empty, there is a large leak, the client decided not to do the leak detector is interested in a new system

The breaker box is bad, it has to be replaced the customer is not happy

The capacitor and contactor were bad, these two were replaced Vacuumed and flushed condensate drain Capacitor 40/5 1 pole contactor System running and operating at this time

the capacitor was bad 45/5

There is an electrical problem on the boat. There is no power in the hair handler or the condenser. An electrician will come in May. After that, he will call us again.

the condenser breaker is bad It's not a recall, it's a different problem. She decided to replace the breaker herself.

Full system Vertical install includes: Remove and dispose of existing equipment and materials. Install new air handler in existing location. Install new outdoor unit at existing location on pad at existing location. Mastic seal immediate duct connections. Safety overflow switch for drain line. Verify proper condensate drainage with Drain Solve. Recover existing refrigerant per EPA standards. Flush and pressure test copper lines. Reconnect Air Handler and Condenser to existing electrical circuits. (Electrical safety: We will ensure your system is installed safely and according to code). Any unforseen electrical upgrades not included in initial proposal will be at the expense of the homeowner. Charge system and adjust fan speed if necessary to ensure maximum efficiency. Permits and Inspections of AHRI certified equipment installed to code. All work to be done in a neat and professional manner in accordance with existing codes by trained technicians. Satisfaction Guaranteed

Upon arrival unit was not working . Cleaning drain line evaporated drain pan and primary drain pan . Add drain line solution and tested with water to make sure is draining. Also noticed that drain line is pitched and will cause problem in the future . Recommend customer to replace drain line and add iFLO device to keep that drain pan clean. Customer needs a quote for a new drainline

IAQ-400

Customer want to check the installation of the 2 new condensers. Condensers were installed on top of concrete bricks and are not safely connected. Customer need to find here evaluation certificate and send to the office so we know how high the condenser should be and we send her a quote

Remove 6 supply flex lines and 1 return flex line. Install new flex ducts and strap up high with canvas straps. Seal with a hard cast mastic. Upon arrival, meet and greet with customer, go over Work scheduled for the day get started tearing out all old ductwork to replace with new from Plenum to boots seal boots to ceiling and reseal all boots and Plenum clean unit with clean spray and wipes. Everything is complete job is finished.

The condensate drain was clogged Vacuum and flushed with drain solve System running and operating at this time

Checked all major components on the unit: compressor, capacitors, fan motors, Freon levels, flushed drain line , checked filters. Based on readings compressor is working hard and unit is old recommend to customer to add a hard start kit on the unit to make compressor work smoother. Also the blower wheel is dirty and need to be cleaned

The disconnect was replaced Completed full maintenance on split system Checked capacitor and contactor Checked compressor and fans amps Checked refrigerant levels and temperature Tested float switch Vacuumed and flushed condensate drain Took sir temperature on supply and return System running and operating at this time

Box of filters 20x20x1

Checked all major come on the ac unit: compressor fan motors , capacitor, Freon levels, temp differentials, flushed drain line, checked filters. Based on readings Unit is operation as designed. The insulation on copper line outside was ripped off. Customer agreed to replace it today. Replaced 4 ft of insulation

Checked all major come on the ac unit: compressor fan motors , capacitor, Freon levels, temp differentials, flushed drain line, checked filters. Based on readings 45/4 Capacitor was going bad customer agreed and replaced it. Everything else is working fine.

The chilled water system is not serviceable. The client is selling g the home soon. We will refund the client the amount for the contract, and only charge her for the service call today.

Performed visual inspection and checked delta T. The system does turn on, but due to condenser underwater, it may be advisable to replace the system. This could be a fire hazard and system warranty has been voided. Comfort advisor met us on site to give replacement options.